Support Forum

map for turbo charge! for yxz1000r non spotshift ?

2»

Comments

  • pamotoracing.com@gmail.compamotoracing.com@gmail.com Posts: 30Verified User

    hi ween i put in all fuel map 25% +more,,, it work perfectly always nice responde but steel i don´t now what shod be my AFR target so i don't overheat my engine and turbo can u tell me what to work with?

    i'm just trying to get the best tune without damage and play safe !

  • jason@ftecu.comjason@ftecu.com Posts: 484Staff User

    Hi,

    I recommend asking whomever you bought the kit from what they recommend for your target AFR.

    Thanks,

    Jason A.

  • pamotoracing.com@gmail.compamotoracing.com@gmail.com Posts: 30Verified User

    🙄

  • pamotoracing.com@gmail.compamotoracing.com@gmail.com Posts: 30Verified User

    i will do that now its broken!!!!!

  • jason@ftecu.comjason@ftecu.com Posts: 484Staff User
    edited October 2019

    Hi,

    Turboing and tuning a car not originally equipped with a turbo isn't necessarily a walk in the park and we did warn you about engine damage. Please get back to me when you have questions regarding our product I can help with.

    Thanks.

    Jason A.

  • pamotoracing.com@gmail.compamotoracing.com@gmail.com Posts: 30Verified User

    it's not your fault and its not mine the valve gasket blow up and the oil got all out until it stops... this engine was set here in YAmaha importer !!!! i did 100 km on it only problem is not knowing same isus and information to do a good job!

    and i no its not a walk in the park i'm a mechanic over 30 years that's why i did so many questions and same did´t have answers!!!

  • jason@ftecu.comjason@ftecu.com Posts: 484Staff User

    Hi,

    Sorry to hear about your motor troubles. Please get back to me when you have questions regarding our product I can help with.

    Thanks,

    Jason A.

  • pamotoracing.com@gmail.compamotoracing.com@gmail.com Posts: 30Verified User

    the engine lights cams on at 8000 rpm and stays on until red line

    hend running below the 8000 it goes off ...

    the problem refer to sensor map reading the new 3 bar sensor it cams with gytr turbo kit!!!! ...

    is it possible to eliminate definatli this error from ecu ?

    thanks.

  • jason@ftecu.comjason@ftecu.com Posts: 484Staff User

    Hi,

    If you are getting a CEL under boost please go to your Manifold DTC window and set both high values to 5.00

    Thanks,

    Jason A.

  • jason@ftecu.comjason@ftecu.com Posts: 484Staff User

    Hi,

    I have another turbo file I'd like you to try. I will email it to you.

    Thanks,

    Jason A.

  • pamotoracing.com@gmail.compamotoracing.com@gmail.com Posts: 30Verified User

    I RECIVIT

    i will try that and let u now my point thanks

    .

  • jason@ftecu.comjason@ftecu.com Posts: 484Staff User

    Hi,

    Please let me know your results.

    Thanks,

    Jason A.

  • pamotoracing.com@gmail.compamotoracing.com@gmail.com Posts: 30Verified User

    hi

    i note that the new map is very different on ignition timing ....not on fuel ,...and that was the main problem on the engine because of detonation on the 3 piston😥 ....i will build the engine and try to use the new map🤔🧐

    can u tell me the part number for the cable to read errors on the ecu?

  • jason@ftecu.comjason@ftecu.com Posts: 484Staff User

    Hi,

    You should be able to put your YXZ into diag mode to read codes by holding down select and reset at the same time, then turn the key on, keep holding down select and reset for another 5 seconds or so, then you will see error codes on the dash display.

    Thanks,

    Jason A.

  • pamotoracing.com@gmail.compamotoracing.com@gmail.com Posts: 30Verified User

    thanks...

  • fcro@icloud.comfcro@icloud.com Posts: 1Verified User

    Hello!

    Im new to the forum!

    I race a Yxz with non turbo. Im planing on turbo my car. Can I use the sidewinder maps and a 3 bar map sensor on the car?

    I will make my own turbo kit.


    thanks

  • pamotoracing.com@gmail.compamotoracing.com@gmail.com Posts: 30Verified User

  • pamotoracing.com@gmail.compamotoracing.com@gmail.com Posts: 30Verified User

    Is this normal?

  • hayes_matt@comcast.nethayes_matt@comcast.net Posts: 5Verified User

    Can you tell me how much boost and what size injectors this turbo file is mapped for?

  • hayes_matt@comcast.nethayes_matt@comcast.net Posts: 5Verified User

    In the accel enrichment map, what do the 0-106 numbers down the left side represent?

    Same question about the ignition map 0-100. Are these TP?

  • jason@ftecu.comjason@ftecu.com Posts: 484Staff User

    Hi,

    Who sold you a turbo file and which one do you have?

    Yes those values are TPS.

    Thanks,

    Jason A.

  • hayes_matt@comcast.nethayes_matt@comcast.net Posts: 5Verified User

    I haven't bought a turbo file yet. I saw in a previous post that you guys have a turbo file for sale for $100. I was asking how much boost is this turbo file setup for, and what size injectors, and what fuel?

  • jason@ftecu.comjason@ftecu.com Posts: 484Staff User

    Hi,

    Please email me if you have any further questions.

    Thanks,

    Jason A.

  • pamotoracing.com@gmail.compamotoracing.com@gmail.com Posts: 30Verified User

    what i can say is this map or the ecu is limited to my YXZ i have to put a PCV to increase the injector full this is why i add problems in the past .... i have try in all ways and nating works, exept with the PCV on

  • pamotoracing.com@gmail.compamotoracing.com@gmail.com Posts: 30Verified User

    i have try to increase table values and it doesn't change the AFR reading? can same one tell me what is the problem it looks its block from factory and accepts the trim values but don't change them! in i missing something?

Sign In or Register to comment.