English
Arabic
Chinese
Dutch
Finnish
French
German
Hebrew
Hindi
Italian
Japanese
Korean
Polish
Portuguese
Russian
Spanish
Swedish
pamotoracing.com@gmail.com
pamotoracing.com@gmail.com
About
- Username
- pamotoracing.com@gmail.com
- Joined
- Visits
- 77
- Last Active
- Roles
- Verified User
- Posts
- 33
Comments
-
https://forum.ftecu.com/discussion/comment/2915#Comment_2915 thanks one more time!
-
past 2 days hi have try so many sings in this unit ... and i alternate the injector latency and now i have more fuel going in! ... this takes a lot off time to get nooing what to do and to go from i don't get to work on the ECU on real time ridi…
-
https://forum.ftecu.com/discussion/comment/1401#Comment_1401 i have done this and it looks its ok now
-
i have try to increase table values and it doesn't change the AFR reading? can same one tell me what is the problem it looks its block from factory and accepts the trim values but don't change them! in i missing something?
-
what i can say is this map or the ecu is limited to my YXZ i have to put a PCV to increase the injector full this is why i add problems in the past .... i have try in all ways and nating works, exept with the PCV on
-
Is this normal?
-
thanks...
-
hi i note that the new map is very different on ignition timing ....not on fuel ,...and that was the main problem on the engine because of detonation on the 3 piston ....i will build the engine and try to use the new map can u tell me the part num…
-
I RECIVIT i will try that and let u now my point thanks .
-
the engine lights cams on at 8000 rpm and stays on until red line hend running below the 8000 it goes off ... the problem refer to sensor map reading the new 3 bar sensor it cams with gytr turbo kit!!!! ... is it possible to eliminate definatli th…
-
https://forum.ftecu.com/discussion/comment/1368#Comment_1368 it's not your fault and its not mine the valve gasket blow up and the oil got all out until it stops... this engine was set here in YAmaha importer !!!! i did 100 km on it only problem is…
-
i will do that now its broken!!!!!
-
hi ween i put in all fuel map 25% +more,,, it work perfectly always nice responde but steel i don´t now what shod be my AFR target so i don't overheat my engine and turbo can u tell me what to work with? i'm just trying to get the best tune without…
-
can u tell me what is translation for " AIS-boost controller"?
-
https://forum.ftecu.com/discussion/comment/1319#Comment_1319 i understand and can u tell me what tires size u are running what gas octane numbers exhaust etc etc
-
11 11 11 11 11 11 11 11 11 11 11 11 11 11 11 11 0 0 0 0 23 23 23 23 23 23 23 23 23 23 23 23 23 23 23 23 0 0 0 0 23 23 23 23 23 23 23 23 23 23 23 23 23 23 23 23 0 0 0 0 18 18 18 12 12 12 12 12 12 12 12 12 12 12 12 12 0 0 0 0 18 18 18 12 12 12 12 12 1…
-
hi i will try that and let u now ... thanks once again ;)
-
between 1500 to 4750 rpm and tps 2 and 12 more or less... now i´m working on "enable boost mapping" buy it self is working must better ,...i really sink if its to lean it can damust the engine! because i'm using a different exhaust mufler (trini…
-
i would like to see between 12.8>13.4 its the best race mod or not?
-
https://forum.ftecu.com/discussion/comment/1292#Comment_1292 thanks the car is running on poorly fuel, the afr is bettuine 14.8 17.00 before it builds boost ! i´m running the gytr map sensor... that problem is ok i believe on top end its seams…
-
its mines -13.11=0.250 volts
-
just received the file and the first test was to poor not good respond at star of acceleration ect mine was working better on bosch sensor i adapt ,.... but i understand this map is just a base set-up. i do not want to run a stock muffler and here …
-
https://forum.ftecu.com/discussion/comment/1273#Comment_1273 that's what i need :) mike from velox racing will contact u ....tanks a lot
-
https://forum.ftecu.com/discussion/comment/1237#Comment_1237 i already star to make a fuel map but i have a problem with the calibration of the 3 bar sensor map that cums with the turbo gytr kit ,...i can´t change this calibration on my ecu so i put…
-
i have spoke with Mike from velox he will contact u for the file...
-
i can buy direct from u and u send me the file? ...just give me your account number for pay pal transfer....
-
here in europe wee have a lot of issus on turbo cars i have make 5 yxz´s non turbo and they stay good and lots of race on them .... that map runs with normal fuel and what octane ? i don't have an account i by from velox racing in uk!!!.... i alread…
-
thanks... i have two cars one is f8t86171 2hc-00 5X27 and the new is f6t86173 2hc-10 6511 part number the first is already flash ...