English
Arabic
Chinese
Dutch
Finnish
French
German
Hebrew
Hindi
Italian
Japanese
Korean
Polish
Portuguese
Russian
Spanish
Swedish
Arab.riders@yahoo.com
Arab.riders@yahoo.com
About
- Username
- Arab.riders@yahoo.com
- Joined
- Visits
- 51
- Last Active
- Roles
- Verified User
- Posts
- 33
Comments
-
Any instruction for sending back?
-
Ok. I'm going to send both unti. Is the Yamaha R6 2017 and Yamaha R1 have the same controller? I have third kit, I want to test also before I send. Thanks
-
Yes, I'm sure I flashed the ECU with active tune license. Yes, the monitor only can be done while bike is running. Thanks
-
Hello, I have the same issue on Yamaha R1. I had purchased 2 kits to install on 2 bikes. After testing the first kit,in the monitor view I got the same message "Awaiting Lambda hardware". Then I replaced the controller and the lambda with the 2nd ne…
-
regarding the wiring, any 5V wire can work? I’m sending my harness for modification, should I tell them to pull a 5V wire from the EXUP valve or from any where from the harness? Thanks
-
Should I send you my ECU along with my immobilizer? Thanks
-
It’s so boring to flash the ECU many times, I don’t think the other maps are going to work. I tried third party map, 3 more US files and JP one. Please advise for other solution. Thanks
-
There are two red wires. Which one is for powering? is it possible to write old model image just to erase the memory then write the new model? what is the IGN switch feature? Thanks
-
All the other US files cannot activate the shifter so I didn't try them. I had replaced my OEM harness with a US harness. Then I removed the bike side harness to the new one but now the I got a message "No response" I removed the wires and reinstal…
-
I believe I was using 32920-17K90. Thanks
-
https://forum.ftecu.com/uploads/204/SINFY7BI4T31.jpeg
-
As per the service manual and test. The red wire is 5V and the black/Brown is ground. When I close the circuit the fuel pump stop. When I open the circuit the fuel pump work. It is like a kill switch not a pit lane limiter?! There are more 3 wires. …
-
What is the feature IGN Switch (Disable/Enable)? Is it related
-
Just to share information, all of the following files can not activate the shifter. 32920-17Kf3, 93, 90, L0, N0, D3, 62, 72, 82, D2 & F2. Thanks
-
Hello, can you advise the part number? I tried many ECU image without success. Thanks
-
Any help how to activate and connect the button? Thanks
-
I tried another image ECU # 32920-17K90 unrestricted and working now in both ways. is it OK to keep this image file? Thanks
-
The error message was for the unrestricted image. for the stock image for same ECU #, the error message is different. “Unknown data in storage location. Please try another file or contact support”
-
Yes, I just tried both directions. All not working. Should I try different ECU image? Or it’s not possible for different ECU number? Also, in the ECU modules>> QS Launch control pit limiter; can not be activated. A message pop up “Error, locating sp…
-
I removed the FTECU sensor and install the OEM sensor and still the same issue. The shifter was working fine before flashing the ECU on normal pattern. Now in GP pattern not working.
-
Thank you
-
Would you upload the installation file for Type 7 QS harness? It is not available to review
-
Hello, maybe I didn’t describe well. I mean if the gear sensor is not connected on 2017-2019 R6 model. The blipper will work or no? Thanks
-
Even the ECU upgraded