Support Forum

Yamaha Auto-Blipper Clutchless Downshifting Activation License

tallerlz520@yahoo.com.artallerlz520@yahoo.com.ar Posts: 40Verified User

hi,

activation license send by email?

«1

Comments

  • kento_ftecukento_ftecu Posts: 776Staff User

    No, you have to order it through your account on our site, and then it gets applied to your account.

  • tallerlz520@yahoo.com.artallerlz520@yahoo.com.ar Posts: 40Verified User

    paid, I need autobliper code

  • tallerlz520@yahoo.com.artallerlz520@yahoo.com.ar Posts: 40Verified User

    I need to activate autobliper

  • kento_ftecukento_ftecu Posts: 776Staff User

    The Auto-Blip feature has been added to your account. Please note that it will be assigned to the first license that you activate the file feature on when it is flashed. You will see a warning pop-up stating that the feature requires special authorization, but that is a standard message whenever the Auto-Blip feature is enabled on a file.

  • tallerlz520@yahoo.com.artallerlz520@yahoo.com.ar Posts: 40Verified User

    quick shifter yes

    autobliper does not work

    error code P1400

  • tallerlz520@yahoo.com.artallerlz520@yahoo.com.ar Posts: 40Verified User

    the red /brown wire disconnected?

  • kento_ftecukento_ftecu Posts: 776Staff User

    That error code is for your AIS. If you have a full exhaust system and have disconnected the AIS, you need to go to your Diagnostics Code Manager and uncheck the box associated with error code.

    Make sure that the auto-blip harness connector that has the extra wire running to the ECU connector (that is your auto-blip connector) is in the position that is activated when you downshift. If your gearshift linkage pushes on the sensor when you downshift, make sure that connector is connected to the sensor wire lead for push.

    Also, you can check your sensor function following this video test: https://www.youtube.com/watch?v=QgrdBm-EjCo

  • tallerlz520@yahoo.com.artallerlz520@yahoo.com.ar Posts: 40Verified User

    NO BLIPER

    CODE P062F

  • kento_ftecukento_ftecu Posts: 776Staff User

    Please go to the Diagnostics Code Manager in your file and uncheck the box associated with that error code.

    Did you check the connectors and the sensor?

  • tallerlz520@yahoo.com.artallerlz520@yahoo.com.ar Posts: 40Verified User

    bliper does not work

    codes ok

    sensor ok

    quickshifter ok

  • kento_ftecukento_ftecu Posts: 776Staff User

    What were the readings you got from the multitester for the sensor?

  • kento_ftecukento_ftecu Posts: 776Staff User

    Did you enable the Auto-Blip feature on the file and flash that into the ECU?

  • kento_ftecukento_ftecu Posts: 776Staff User

    What about the sensor connectors, did you check that your Auto-Blip connector from the harness is leading to the correct connector from the sensor?

  • tallerlz520@yahoo.com.artallerlz520@yahoo.com.ar Posts: 40Verified User

    Impossible to write


    “Status: Fail: Invalid ECU image”???

  • tallerlz520@yahoo.com.artallerlz520@yahoo.com.ar Posts: 40Verified User

    I'm 9 hours ago with this problem

  • kento_ftecukento_ftecu Posts: 776Staff User

    That means you are trying to write in the wrong file.

    What is your ECU part number? And which file are you using?

  • tallerlz520@yahoo.com.artallerlz520@yahoo.com.ar Posts: 40Verified User

    File BX4-8591A-00 ecu: idem

    I managed to write but bliper doesn't work


    Here is Eastern time, tomorrow I follow you

  • kento_ftecukento_ftecu Posts: 776Staff User

    We need the ECU part number please.

    You may have also changed something on the file that doesn't work with what modifications have been done to the motorcycle.

  • tallerlz520@yahoo.com.artallerlz520@yahoo.com.ar Posts: 40Verified User

    Harness R1 2015/2016 vs harness R1 2017

    Is the diagram the same?

    Is it only different from the ecu terminal?

  • tallerlz520@yahoo.com.artallerlz520@yahoo.com.ar Posts: 40Verified User

    BX4-8591A-00

    112600-5051

    TBDFZ A

  • jason@ftecu.comjason@ftecu.com Posts: 1,071Staff User

    Hi,

    The autoblip harness for the 15-16 R1 is different than the 17 R1. What autoblip harness do you have?

    Thanks,

    Jason A.

  • tallerlz520@yahoo.com.artallerlz520@yahoo.com.ar Posts: 40Verified User

    My bike was 2015 now it is 2017 I use the cable 2015

    missing voltage on pin 12 ecu

    that's the problem

  • tallerlz520@yahoo.com.artallerlz520@yahoo.com.ar Posts: 40Verified User

    I need to modify the cable

  • tallerlz520@yahoo.com.artallerlz520@yahoo.com.ar Posts: 40Verified User

    The 2017 cable is for sale?

  • kento_ftecukento_ftecu Posts: 776Staff User

    My bike was 2015 now it is 2017 I use the cable 2015

    missing voltage on pin 12 ecu

    that's the problem

    These are the details that we need to know right from the start. It helps to avoid wasting time asking questions trying to narrow down problem areas.

    Yes, the auto-blip harness for the 2017 R1 is available. Go to the 2015-2017 R1 page, and when you click on the Auto-Blip kit page, the drop-down menu shows a kit for the 2017 R1 with stock harness.

  • tallerlz520@yahoo.com.artallerlz520@yahoo.com.ar Posts: 40Verified User

    Harnes alone is not available

    It was not my intention to complicate

    you should sell the harness separately

    Thanks and sorry

    pd: I lost $ 200

  • kento_ftecukento_ftecu Posts: 776Staff User

    We can create an invoice to buy an auto-blip harness separately if you have an account with us.

  • tallerlz520@yahoo.com.artallerlz520@yahoo.com.ar Posts: 40Verified User

    Yes, I have an account

  • tallerlz520@yahoo.com.artallerlz520@yahoo.com.ar Posts: 40Verified User

    How do I buy the harness?

  • kento_ftecukento_ftecu Posts: 776Staff User

    We will create an invoice, and then you will receive an email with a link so that you can pay for it via your account on ftecu.com. It will be sent out shortly.

Sign In or Register to comment.